Fibex Vibrating Reminder 40mm Watch Manual – English

Charging

Please charge fully before first use.
Gently remove the watch face from the band to reveal the USB contacts.
Plug the watch into your power bank, laptop, or desktop computer as shown in the image below.
A full charge takes about 1 hour and can last 10-35 days. After one minute of charging, the watch will display a blinking blue light. If you don’t see it, rotate the watch face and reinsert it.

When the screen is black, press the top button once to display the time.
Hold down the top button until the hours flash. Press the top button to increase the hours or the bottom button to decrease them.
Hold down the top button until the minutes flash. Press the top button to increase the minutes or the bottom button to decrease them.
Hold down the top button until 12H or 24H shows. Press any button to select either 12-hour or 24-hour format.

To set the alarm time: Press the top button repeatedly until the desired alarm time appears (e.g., alarm 1 at 10:00). Hold down the top button until the hours flash. Press the top button to increase the hours or the bottom button to decrease them. Hold down the top button until the minutes flash. Press the top button to increase the minutes or the bottom button to decrease them.
To turn the individual alarm on/off: After selecting the minutes, quickly hold down the top button to see “A1OF” (or press the top button 5 times when the screen is off to see “A1OF”). Press the bottom button to switch to “A1ON.”
Continue to press the top button to cycle through the next alarms. Repeat the above steps to modify them.

To turn the timer on: When the screen is off, press the bottom button repeatedly to display Cdn, 1, 5, 10, 15, 20, 30, 45, 60, 90, 120, or 180 minutes. When you reach your desired interval, hold down the bottom button until “ON” appears.
Press the bottom button to see the time remaining, press again to see the current time, and again to see the battery level.
To turn the timer off: Press any button to display the time remaining, then hold down the bottom button for 4 seconds until “OFF” appears.

Press the top button once to see the time.
Press the top button twice to check the battery level.
Press the top button three times to display ALM (Alarm).
Press the top button four times to see the time of Alarm 1 (10:00).
Press the top button five times to see A1OF (Alarm 1 OFF).
Press the top button six times to see the time of Alarm 2 (10:00).
Press the top button seven times to see A2OF (Alarm 2 OFF).
Continue to press the top button to cycle through all the next alarms. Note the sequence is alarm time first, then alarm OFF/ON.

When you see the alarm you want to turn on/off (e.g., A2OF), press the bottom button to switch to A2ON (a clock symbol will appear).

Temporarily deactivate all alarms and timer settings. Hold both buttons together for 3 seconds until “SIL” appears (a red silent icon will appear).

Hold both buttons for 3 seconds to reactivate all alarms and timer settings. “VIB” will appear.

Prevent accidental changes to programmed settings. When the screen is off, press the top button to see the time. Press and hold the bottom button for 5 seconds on the “Time” screen to lock (a pink lock icon will appear).
Unlock: Hold down the bottom button for 5 seconds on the “Time” screen to unlock (the lock icon will disappear).

The watch will only light up and show the time when you press the button.
The watch is waterproof for normal use but should not be used in a swimming pool.
You can’t make any changes in lock screen mode. Unlock first, then change the settings.
Alarm 1 has a longer alarm time of 60 seconds, suitable as a wake-up alarm. You can set two more alarms as snooze functions.
All other alarms are 30 seconds long.
The vibration can be stopped immediately by pressing any button.
Alarms automatically repeat on schedule daily.
When the alarm goes off, it vibrates with the time flashing to remind you.
When the timer goes off, it vibrates only, making it discreet.

If the alarms don’t vibrate: